Shaft Clamp

All EPT shaft collars, including quick-clamping collars, are solitary point faced to make sure perpendicularity and proper alignment. This critical manufacturing step assures specific shaft collar face to bore relationship resulting in correct component positioning on the shaft and even pressure on interfaced pieces.
Quick-clamping shaft collars from EPT are produced from high quality metal with type-II sulfuric anodized finishes, with a dark finish about the collar and a precious metal finish in the clamping lever for added visibility. Aluminum collars are corrosion resistant, lighter than different metals, have low inertia and also have nonmagnetic properties. All EPT products happen to be RoHS and REACH compliant. Available typical sizes for the quick-clamping shaft collars will be 0.375” to at least one 1.5” in the inch series and 8 mm to 38 mm in the metric series.
Shaft Collar, System of Measurement Inch, Shaft Locking Type – Couplings 1 Piece Speedy Clamp, Bore Type – Collars Plain Bore, Bore Dia. 3/8 In., Materials – Collars Black Anodized 6061 Aluminum, Outside the house Dia. 1-1/2 In., Width .394 In., Clearance Dia. 1.496 In., Screw Size M3, Screw Material 18-8 300 Series Stainless Steel, Operating Temp. Range -40 Degrees to 200 Degrees F, Criteria RoHS2 Compliant, REACH Compliant
The Shaft Collar 1×3/8, 1/2″ for Key Shaft is made of lightweight Aluminum, the two piece design allows you to install these collars anywhere on a shaft without removing components. Furthermore to reducing the entire weight, the flats enable you to rotate a shaft without marring or gouging the shaft. Easily place the collar on the shaft and tighten the two socket-brain cap screws to protected the collar and a wrench and be positioned on the collar’s flats to rotate the entire shaft/collar assembly.
Made of lightweight Aluminum
Enables you to install these collars anywhere on a shaft without removing components
Just place the collar about the shaft and tighten both socket-head cap screws to secure the collar
Flats allow you to rotate a shaft without marring
Climax Part C-056-S Established Screw Collar is made with T303 STAINLESS, which is effective in corrosive environments. Measurements will be 9/16 in. Bore, 1 in. OD, 7/16 in. Width. It really is effective on hard and smooth shafts. This is a Affordable collar design, and Conveniently installed where main disassembly would otherwise be required.
EPT quick clamping shaft collars collar clamp hinge buy manufacturing 2 1 8 in steel,shaft collar clamp induce manufacturing steel vex clamping design,vex clamping shaft collar collars one particular piece with lever clamp hinge,vex clamping shaft collar clamp 3d model manufacturing quick 1 3 8 in alum,EPT quick clamping shaft collars collar clamp 2pc 1 in steel stainless split with lever,climax metal s shaft collar two piece clamp style EPT quick clamping collars 2pc 1 in steel power,clamp about shaft collars couplings universal clamping collar design with mounting holes 2pc 1 in steel,shaft collar clamp push clamping calculation quick connect collars at best price in,clamp shaft collar clamping collars push calculation speedy connect,stainless steel double split shaft collar with quick clamping clamp hinge induce calculation.
Black Oxide Plated Metal One-Piece Clamping Collar.
Recessed Screw Head provides an outside surface free from important projections for safety.
Design completely engages the shaft without marring.
Greater axial holding ability than established screw collars.
Effective on hard & delicate shafts.
Indefinitely adjustable and easy to remove, one-piece clamping collars are typically used on hard or soft standard round Shaft Clamp china shafts, over a split hub or upon thin wall tube. By using friction to supply superior grip on bars and shafts, sole split collars give sturdier, more trustworthy results in comparison with the set screw design of solid collars. They also offer tremendous axial ability, while reducing shaft distortion for top-notch performance and decreased wear and tear.

The collar clamping mechanism works fast and effectively with simple hands opening of the integral clamping lever, positioning the collar on the shaft, and closing the lever flush with the external surface area of the collar. The look of the cam on the lever and the mating machined surface on the collar assure a tight fit with a maximum axial load of 35 to 120 lbs / 133 to 489 N based on the collar bore size. In scenarios where higher holding power is or clamp axial load is necessary, the quick-clamping collar isn’t the recommended choice. EPT offers a full type of industry-leading one-part and two-part shaft collars created for these applications.

Tags: