The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you need. For work with with 5/8” shaft sizes. Includes set screws. Added Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering readily available requirements and allowing for alterations in shaft size if necessary. The barrel of the split tapered bushing can be split in two spots and can be keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The good thing about the split tapered bushing is it will hold, regardless if the fasteners become loose. Split tapered bushings are interchangeable between manufacturers.

Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are created from high quality engineered materials with superb tolerance. The feature is easy to apply and needs no more alteration. These bushings can fit almost all types of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations put bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total selection of both metric and imperial offered.
Standard range suits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete short reach range offered, for compact light in weight assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for durability and strength. U1 bushings are used in an extensively broad range of applications, including; sprockets, shaves, pulleys, gears, and much more, we likewise offer all of these items. What units this bushing apart may be the high-quality steel construction along with specific manufacturing and top quality control; this ensures that you always get a premium quality regular product. What really units us apart from the other fellas is our experienced expert staff members and our company-wide aim of customer satisfaction.
1. Be sure the tapered cone surfaces of the bushing and the within of the driven merchandise happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or other component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to assure sliding in shape on shaft.
4. With important on shaft, slide the sprocket or other component type to the desired posture on the shaft. Make sure you leave the heads of the cap screws available.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they happen to be pulled up tight. Do not make use of extensions on the wrench handles and don’t allow the sprocket or portion to always be drawn i contact with flange of bushing. At this time there must be a gap between your bushing flange and sprocket, make certain this gap will not close.
Double split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for confident drive and increased torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to keep concentric bores
Available in in ., metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys upon both the shaft and merchandise to supply the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper provides the highest degree of mechanical locking product to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need. For employ with 5/8” shaft sizes. Includes set screws. Extra Features: Made of Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering on hand requirements and enabling improvements in shaft size if important. The barrel of the split tapered bushing is split in two areas and is usually keyed to the shaft. The barrel OD can be keyed to the drive component as well. The advantage of the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.